England Finance

Oct 17 2017

Sockets programming in Java: A tutorial #java #programming #services


Sockets programming in Java: A tutorial

Java I/O and NIO.2

This classic JavaWorld tutorial presents an introduction to sockets programming over TCP/IP networks and demonstrates how to write client/server applications in Java.

A bit of history

The Unix input/output (I/O) system follows a paradigm usually referred to as Open-Read-Write-Close. Before a user process can perform I/O operations, it calls Open to specify and obtain permissions for the file or device to be used. Once an object has been opened, the user process makes one or more calls to Read or Write data. Read reads data from the object and transfers it to the user process, while Write transfers data from the user process to the object. After all transfer operations are complete, the user process calls Close to inform the operating system that it has finished using that object.

More about Java I/O

Learn how to squeeze maximum performance out of Java’s nonblocking I/O classes with these how-tos:

When facilities for InterProcess Communication (IPC) and networking were added to Unix, the idea was to make the interface to IPC similar to that of file I/O. In Unix, a process has a set of I/O descriptors that one reads from and writes to. These descriptors may refer to files, devices, or communication channels (sockets). The lifetime of a descriptor is made up of three phases: creation (open socket), reading and writing (receive and send to socket), and destruction (close socket).

The IPC interface in BSD-like versions of Unix is implemented as a layer over the network TCP and UDP protocols. Message destinations are specified as socket addresses; each socket address is a communication identifier that consists of a port number and an Internet address.

The IPC operations are based on socket pairs, one belonging to a communication process. IPC is done by exchanging some data through transmitting that data in a message between a socket in one process and another socket in another process. When messages are sent, the messages are queued at the sending socket until the underlying network protocol has transmitted them. When they arrive, the messages are queued at the receiving socket until the receiving process makes the necessary calls to receive them.

TCP/IP and UDP/IP communications

There are two communication protocols that one can use for socket programming: datagram communication and stream communication.

The datagram communication protocol, known as UDP (user datagram protocol), is a connectionless protocol, meaning that each time you send datagrams, you also need to send the local socket descriptor and the receiving socket’s address. As you can tell, additional data must be sent each time a communication is made.

The stream communication protocol is known as TCP (transfer control protocol). Unlike UDP, TCP is a connection-oriented protocol. In order to do communication over the TCP protocol, a connection must first be established between the pair of sockets. While one of the sockets listens for a connection request (server), the other asks for a connection (client). Once two sockets have been connected, they can be used to transmit data in both (or either one of the) directions.

Now, you might ask what protocol you should use — UDP or TCP? This depends on the client/server application you are writing. The following discussion shows the differences between the UDP and TCP protocols; this might help you decide which protocol you should use.

In UDP, as you have read above, every time you send a datagram, you have to send the local descriptor and the socket address of the receiving socket along with it. Since TCP is a connection-oriented protocol, on the other hand, a connection must be established before communications between the pair of sockets start. So there is a connection setup time in TCP.

In UDP, there is a size limit of 64 kilobytes on datagrams you can send to a specified location, while in TCP there is no limit. Once a connection is established, the pair of sockets behaves like streams: All available data are read immediately in the same order in which they are received.

UDP is an unreliable protocol — there is no guarantee that the datagrams you have sent will be received in the same order by the receiving socket. On the other hand, TCP is a reliable protocol; it is guaranteed that the packets you send will be received in the order in which they were sent.

In short, TCP is useful for implementing network services — such as remote login (rlogin, telnet) and file transfer (FTP) — which require data of indefinite length to be transferred. UDP is less complex and incurs fewer overheads. It is often used in implementing client/server applications in distributed systems built over local area networks.

Programming sockets in Java

In this section we will answer the most frequently asked questions about programming sockets in Java. Then we will show some examples of how to write client and server applications.

Note:In this tutorial we will show how to program sockets in Java using the TCP/IP protocol only since it is more widely used than UDP/IP. Also: All the classes related to sockets are in the java.net package, so make sure to import that package when you program sockets.

How do I open a socket?

If you are programming a client, then you would open a socket like this:

Where Machine name is the machine you are trying to open a connection to, and PortNumber is the port (a number) on which the server you are trying to connect to is running. When selecting a port number, you should note that port numbers between 0 and 1,023 are reserved for privileged users (that is, super user or root). These port numbers are reserved for standard services, such as email, FTP, and HTTP. When selecting a port number for your server, select one that is greater than 1,023!

In the example above, we didn’t make use of exception handling, however, it is a good idea to handle exceptions. (From now on, all our code will handle exceptions!) The above can be written as:

If you are programming a server, then this is how you open a socket:

When implementing a server you also need to create a socket object from the ServerSocket in order to listen for and accept connections from clients.

How do I create an input stream?

On the client side, you can use the DataInputStream class to create an input stream to receive response from the server:

The class DataInputStream allows you to read lines of text and Java primitive data types in a portable way. It has methods such as read. readChar, readInt, readDouble, and readLine. Use whichever function you think suits your needs depending on the type of data that you receive from the server.

On the server side, you can use DataInputStream to receive input from the client:

How do I create an output stream?

On the client side, you can create an output stream to send information to the server socket using the class PrintStream or DataOutputStream of java.io:

The class PrintStream has methods for displaying textual representation of Java primitive data types. Its Write and println methods are important here. Also, you may want to use the DataOutputStream.

The class DataOutputStream allows you to write Java primitive data types; many of its methods write a single Java primitive type to the output stream. The method writeBytes is a useful one.

On the server side, you can use the class PrintStream to send information to the client.

Note: You can use the class DataOutputStream as mentioned above.

How do I close sockets?

You should always close the output and input stream before you close the socket.

On the client side:

On the server side:


In this section we will write two applications: a simple SMTP (simple mail transfer protocol) client, and a simple echo server.

Let’s write an SMTP (simple mail transfer protocol) client — one so simple that we have all the data encapsulated within the program. You may change the code around to suit your needs. An interesting modification would be to change it so that you accept the data from the command-line argument and also get the input (the body of the message) from standard input. Try to modify it so that it behaves the same as the mail program that comes with Unix.

When programming a client, you must follow these four steps:

  • Open a socket.
  • Open an input and output stream to the socket.
  • Read from and write to the socket according to the server’s protocol.
  • Clean up.

These steps are pretty much the same for all clients. The only step that varies is step three, since it depends on the server you are talking to.

Now let’s write a server. This server is very similar to the echo server running on port 7. Basically, the echo server receives text from the client and then sends that exact text back to the client. This is just about the simplest server you can write. Note that this server handles only one client. Try to modify it to handle multiple clients using threads.

Java I/O and NIO.2

Written by admin

Leave a Reply

Your email address will not be published. Required fields are marked *